Excel Knives, blades and tools

Excel’s US-made craft knives and blades are the ones model makers swear by, from the classic K1 to the heavier K2 and K5. Saws, tweezers, clamps and cutting mats complete the bench.

K1 KnifeK2 KnifeK5 Knife

Start with the handle

Almost everything written about craft knives is about the blade. The handle decides three things the blade cannot: which blades you can fit, how much pressure you can safely apply, and whether your hand still works after an hour.

K1 KnifeK26 KnifeK18 Knife

Light duty, for detail

Paper, card, foamboard, thin plastic sheet, film, decals and model cleanup. The K1 is the one to start with.

See all light-duty knives
K2 KnifeK5 KnifeK6 Knife

Medium and heavy, for pressure

Chipboard, leather, dense foam, thick card, soft wood. A larger collet holds a heavier blade, so nothing flexes when you lean on it.

See all medium and heavy knives
K9 KnifeK870 KnifeK820 Hand Thread Screw (Carded)

Utility knives

Cardboard, carpet, packaging and rope, where a craft blade would simply fold.

See all utility knives
K10 KnifeK73 KnifeK850 Plastic 18mm (Carded)

Snap-off knives

Snap-off blades for anything that blunts fast.

See all snap-off knives

Which to buy first

Most people end up with two: a light knife for detail and a heavier one for everything that needs pushing. That pair covers more ground than any single knife.

The mistake most people make is pushing harder on a light knife rather than picking up a heavier one. That is how fine blades snap and how cuts wander.

What you mostly cut Start with
Paper, card, film, model kits K1
Long sessions, hand fatigue K26
Foamboard, chipboard, leather K2
Thick foam, heavy card, soft wood K5
Curves in vinyl or film K4 with a swivel blade
Carving and shaping K7
Packaging, cardboard, rope K60

What the blade was ground to do

A blade that tears foam will slice card cleanly, and a blade that carves balsa beautifully will skate off styrene. There are only a handful of shapes, and each does one job.

#11 Double Honed Blade#21 Stainless Steel Blade#16 Stencil Edge Blade

Straight edge

Cuts on the draw, along a rule or freehand. Card, paper, thin sheet, leather, masking film. The #11 is the one most people mean by a scalpel blade.

See all straight edge blades
#17 Small Chisel Blade#18 Large Chisel Blade#5 Angled Chisel Blade

Chisel edge

Ground square across the tip, so it pares rather than slices. It cannot dig in, which is why it is the tool for mould lines and dried glue.

See all chisel edge blades
#10 Curved Edge Blade#22 Curved Edge Blade#12 Mini Curved Blade

Curved edge

The contact point rolls along the edge, so long sweeping cuts stay continuous. For cutting to a shape rather than to a line.

See all curved edge blades
#13 Fine Saw Blade#15 Narrow Saw BladeSaw Blade #27, Shank 0.345" (0.88 cm) (5 pcs) (Carded)

Saw and serrated

Cuts on the stroke, not on pressure. Wood and rod need teeth to start; foam and rubber need an edge that works sideways.

See all saw blades

What are you cutting?

Pick a material and we will show the Excel knife and blades suited to it. Every recommendation is Excel's own, from their product copy or application pages.

Carbon steel or stainless?

Nearly every precision blade is one of two steels, and the choice is a single trade: carbon steel gets sharper, stainless steel survives neglect.

Carbon takes a finer edge and holds it longer, but left damp it starts to rust at the edge within hours. Stainless is slightly less keen and slightly tougher, so it flexes where carbon would snap.

Test it yourself: the #11 double honed and the #21 stainless are the same fine profile in the two steels.

If this is you Buy
You cut in sessions and put tools away properly Carbon
The finish of the cut is the finished surface Carbon
You go through blades quickly anyway Carbon
Your workspace is a garage, shed or unheated studio Stainless
Tools live loose in a drawer or a toolbox Stainless
You work around water, clay or plaster Stainless
You snap fine points regularly Stainless

Keeping a blade sharp

A craft blade is ground to an edge a few micrometres thick, so rust is not cosmetic: the blade that was sharp on Friday drags on Monday. Above about 50% humidity, which in Britain is most of the year, corrosion speeds up sharply.

Get the residue off

Adhesive, resin, plaster and some papers hold moisture against the steel. Wipe the blade before it goes away.

Dry it properly

If you cleaned with anything wet, alcohol included, let it flash off completely before storing.

Wipe off your hands

Skin carries salts and acids. A fingerprint on bare steel is an etched fingerprint a few weeks later.

Leave a film of oil

Very little. For blades used on paper or card, a dry PTFE lubricant protects without marking the work.

Guides

Sixteen longer reads, from a first knife to the tools for an architecture course.

A complete guide to precision craft knives

What separates a light-duty handle from a heavy-duty one, and which to reach for first.

Blade shapes and edges explained

Point, chisel, curved and concave: what each shape is ground to do.

Carbon steel or stainless steel?

Carbon takes a keener edge, stainless resists rust. Which matters more for your work.

Which blades cut foam cleanly

Why foam tears rather than cuts, and the blades and technique that stop it.

Model kits: number 11, chisel or curved?

Removing parts from a sprue, cleaning mould lines and scraping seams, blade by blade.

Choosing a heavy-duty utility blade

Where a snap-off blade stops being the right tool and a utility knife starts.

Surgical blade sizes, and what each one is for

The numbered scalpel blades, what each profile suits, and where they beat a craft knife.

How to stop your blades rusting

Storage, handling and the two habits that cost carbon steel blades their edge.

Choosing knives, scissors and hand tools if you are left-handed

Why most blades are ground for right-handed use, and which tools work either way.

Choosing tweezers for fine work

Straight, angled, fine point and reverse action, and the jobs each one suits.

Sanding tools for woodwork and model building

Sticks, files and papers, and the grit order that stops you polishing in a scratch.

Wood carving tools, from first cuts to fine detail

Gouges, chisels and carving blades, and a sensible order to buy them in.

Clay modelling tools for beginners

A short starting kit for sculpting, and what each tool actually does.

Tools for architecture students

What to buy for first-year model making, and what can wait until later.

Five tools for EVA foam cosplay builds

Cutting, bevelling and shaping EVA foam without chewing the edge.

Craft kits by hobby

Which boxed sets are worth it, and when buying the tools separately is cheaper.

Questions about Excel knives

Is an Excel knife the same as an X-Acto knife?

X-Acto is an American brand name that became a generic term over there, the way Hoover did here. A tutorial saying "X-Acto knife" means nothing more specific than a light-duty craft knife like the K1.

Which knife should I buy first?

The K1 for paper, card, film and model kits. If you cut thicker materials too, add a K2 or K5. Most people end up with one light and one heavy knife.

Can I scrape with a number 11 blade?

It is not a scraper. Its point concentrates all your pressure on one spot, so it digs in. A chisel blade such as the #17 spreads the pressure and shaves material away in layers.

Why does my foam come out with a wavy, crushed edge?

The blade is not blunt, it is the wrong shape. Soft, springy materials get crushed flat by a downward cut and need a serrated edge that works sideways.

Why did my blade go blunt in the drawer?

Rust at the edge, long before anything shows. Wipe and dry blades before putting them away, and keep a light film of oil on them. Or choose stainless.

Shop Excel

Knives, blades and tools, grouped the way you would look for them.

Skip to results list

Filters

152 items
Column grid
Column grid

Filter